Monday, May 16, 2016

1963 Ford Ranchero




I was out this morning and took a new photo of the Ranchero.

Saturday, October 31, 2015

I got my new wheels and tires installed finally. I installed P195/60r14 tires both front and rear due to the size limitations for the rear tires. I only have about 1/2 inch between the fender well and the edge of the tire.


Wednesday, October 14, 2015

New Wheels

I found a set of 4 of these on CL the other day for $300.00. They are 7x14 American Racing AR23 wheels with a -6 offset. The tires are shot but for the price I couldn't go wrong. The AR23's are discontinued in the 4 lug version and I haven't ever seen them on a Ranchero or early Falcon so they should be unique.


Tuesday, September 22, 2015

Headers and dual exhaust

I installed a chrome split header I purchased on ebay and dual exhaust with turbo mufflers. I had a bit of a hard time installing the header because of the taller 250 cuin I6 engine. Also the headers came very close to the starter so I changed it out to a 'mini starter' also purchased from ebay. Here's a photo of the headers and video of the dual exhaust.

 Video

Friday, November 28, 2014

Replaced Odometer

The speedometer housing in the Ranchero, is from a 1962-63 Mercury Comet. It fits great however the odometer hasn't worked since I've owned the car. I've looked for a replacement but never was able to locate one. I did find a few replacement speedometer housings but the cost was prohibitive. I was finally able to locate just the speedometer (with odo) for a 1961 Ford Falcon. With quite a bit of research it appeared that it probably would work in the Merc housing. I went ahead and bought it ($53.00 with shipping). The only modifications I made were to cut the top 1" or so off of the black back panel since the Merc housing needs that area to cast the illumination for the lights and clear the area that the Merc uses 2 round tubes to direct the high beam and turn signal indicator lights. Here's some photos of the 'old' non-functioning odo.               
And here's a photo of the 'new' speedometer before I modified it.
   The new speedometer / odometer are working great!!!

Wednesday, April 9, 2014

8" rear end installed.

Well I finally got everything together and installed the 'new' 8" Maverick rear end. The 3.00 gear ratio makes a big difference!

I had to get the drive shaft modified again to accept the new u-joint for the 8". While checking it out we discovered that the front u-joint yoke was bad. So basically I had to replace everything but the 'tube'. Now it should last a while.

Everything went smooth, no surprises. The 8" is about 1/4" wider on both sides so the tires stick out that much further. Not enough to be a problem. I haven't tried the 'new' 14 inch tires yet but I will sometime soon.

Hope to get some photos up soon.

Monday, February 3, 2014

Another rear end!

I happened upon a rare 8" four lug rear end from a 71 Ford Maverick a week or so ago. The price was right so I went to Corona to pick it up. After talking with the guy for a while I also was able to get 4 each 14" rims (2 with good tires) a air cleaner housing and the rear end for $80.00. This rear end is heavier duty than the 7 3/4 inch I have now and a big advantage is that it's a 3.00 rather than the 3.50 I have now. So instead of 2900 rpm at 60 mph it will drop to a much less stress 2450. Also with the larger 14" tires it will drop even further to 2375. I probably won't put the tire on for a while as I really don't need new tires yet so I will save them till I can change all four and put new caps and trim rings on the 14's.



Monday, December 2, 2013

It's been a while since I've posted a photo of the car. I drove down to old town Murrieta this morning and parked in front of an old building. I dodged traffic and took this picture.


Thursday, November 7, 2013

Turn signal cancel / rear axle seal

Yesterday I decided to replace the passenger side rear axle seal. It's been leaking since I put the rear end in. Just a little but enough to put gear oil on the driveway and make a mess on the inside of the tire. I had purchased an axle seal a while back, assuming that the rear end was out of a 'sedan'. However when I pulled the old one out it wasn't the same size. After some research I determined that it was actually out of a Ranchero. The rear bearings and axle seals are bigger. Since none of the local parts houses had one I had to make a run to Escondido to pick one up at C&G auto. The new seal was a snap to install.

I also bought a turn signal cancel switch since the one that was in the car was broken. Left hand turns never cancelled. The one I purchased has 2 wires and in reading I wasn't sure it was the correct one, however it was so after removing the steering wheel I pulled the old one and soldered in the wires. The retainer clip was tough but I finally got it installed. Works great.

Monday, November 4, 2013

New motor mounts installed.

My new motor mounts came in so I installed those. Ya gotta love old cars. Only about 15 minutes to install both sides! I did a bit more research on my distributor, engine combination (1971 Ford Torino points type distributor in a 1975 Ford Granada engine) The manuals say to use the 'sticker' to determine the correct initial timing, however since the engine didn't come in the car, no sticker. I searched the internet but there isn't much info. Since the engine is a 1975 Ford had just started with the smog stuff. It originally had a 'duraspark' ignition but since that was swapped out I wasn't sure what I should set the timing at. I had played with using manifold vacuum to set it and found that it was setting is above TDC. I did find some references of setting timing to 0 TDC so figured I would give that a try. The motor starts better now and the 2500 rpm vibration has reduced. Guess I will stick with that for a while.

I ordered a turn signal cancel part for the steering column, hopefully I can get that installed this week. I also need to install the passenger side rear wheel seal as it's leaking just a bit.

Friday, October 18, 2013

A few more updates.

I decided to change out the points, condenser and rotor a while back, nothing wrong with them just figured since I didn't know how old they were, I would change them. I had considered changing over to the Pertronix (electronic) ignition but thought I would save a few bucks (mistake on my part). Anyway about 2 weeks after I switched, I was taking a short trip around the neighborhood and suddenly the engine started to mis. Nothing bad just a slight mis, however it kept getting worse until it got to the point I wasn't sure I would make it home. I struggled and finally made the driveway. It felt like the car was running out of fuel, so I decided to change the fuel pump as again it was looking like it may have been the original 75 pump. I ordered one along with a new 'clear' fuel filter to prefilter the pump. Those got here in a few days and I swapped them out. I tried to start the car and it would turn over and try to run but then stop. I was getting fuel but still wouldn't start. No backfire just wouldn't run. I had rebuilt the carburetor a while but but I wasn't really happy with the end result. The Carter YFA that was on the engine was the original carb and was set up for 1975 standards. (smog stuff). I did some searching on-line and located a 'factory rebuilt' YFA for $85.00 (good price!) on ebay. I ordered it and got it about a week later. Nice carb! rebuilt in about 1985 or so and still in the vacuum sealed package. I installed it but the car still wouldn't run! I came back in and did some searching on the internet, I finally found a "model A" forum and a member was describing the same symptoms I had with my engine. He fixed his by replacing the 'condenser'. Since I had kept my old ones I went out and swapped the 'new' condenser and put the old one back in. She fired right up!!!! I came back inside and ordered the Pertronix ignition system. About a week later I got it installed and now everything runs great! No misses, no stumbles, smooth idle, choke works great, no EGR port on the front of the carb, (that was left open and was always a concern!).

I also ordered a new set of motor mounts. They should be here next week. I am still getting my 2500 and up RPM vibration. Based on the squished appearance of the old ones my guess is, again these are original parts that have never been replaced.





Monday, July 29, 2013

Quick update

Just a quick update.

I need to take some photos to update some of the things I've done lately.

1. added a snap tonneau cover. (the car had the snaps and this just helps cover them up as there is no way to remove them without leaving holes.) I made this myself with tonneau material I found on the internet and snaps. It came out better than I expected.

2. finished up the door panels (they look great!)

3. changed out the exhaust manifold gasket. Broke one of the bolts but there was enough sticking out I could use vise grips to remove it. There was virtually nothing left of the old gasket. I replaced all of the bolts with grade 8 bolts and internal tooth lock washers. The new gasket got rid of most of my 2000 / 2500 rpm vibration! And the engine idles smoother. No exhaust smell in the passenger area either.

Tuesday, May 28, 2013

New door panels

My old "tuck and roll" door panels were starting to look pretty sad. The PO had removed the 'plastic liner' from the door when they installed the panels and the rain got to the fiber board pretty bad. They kinda sagged in the middle and were really looking ragged. I had read an article on replacing the door panels. LINK

I purchase some 'white board' from Lowes, the kind of stuff they use to make marker boards with and turned the 'white' side towards the outside to help with moisture control. Then I made the trip to Joannes. They had the 'head liner foam' in stock and so I started looking for some vinyl to cover them with. I stumbled across some 'costume' material that just 'said' USE ME !! So I bought a couple yards and went to work.

Here's some pictures of the 'white board' and the finished panel. I will take some of it installed and post later.





Wednesday, May 15, 2013

I had some time last weekend to pull the tailshaft extension housing off the C4 automatic. I knew the bushing was bad as the drive shaft had some play on the transmission end. It really wasn't that big of a deal. About 2 1/2 hours for everything. The old bearing did show wear so it was about time. I also changed the seal (again). While I had the cross member out I modified the 'homemade' C4 adapter that the PO had made for the trans. This involved griding down what was left of the downward facing angle iron that was put there to 'strengthen' the mount. It wasn't really necessary as the plate portion was quite strong. It just hungdown and looked ugly. Anyway all back together and it appears it fixed a slight 'cluck' I was hearing when I shifted from reverse to drive.

Thursday, May 2, 2013

Replaced the carburetor to manifold gasket yesterday and also changed the mounting bolts as I got the feeling they were a bit too short. It appears to have helped fix the 'missing' at idle. The engine now purrs like a kitten!

Still chasing the 2000 + vibration problem. I did some reading and it appears that there is a bushing in the C4 transmission extension housing that the driveshaft yoke rides in. Thinking back to when I changed the seal (which is still seeping by the way.) that there was some play in the shaft. I ordered a new bushing and seal today (12.00 or so including shipping.) and will change it out. Looks like I will have to pull the trans extension housing to get to it. Hopefully not that big of a deal.

We shall see.

Tuesday, April 23, 2013

Well a few more additions:

I installed a pair of Monroe air lift shocks on the back. I did this for two reasons. 1. the old shocks were worn out and needed replacement anyways, and 2. I could raise the rear just a bit to give the car a bit of a 'rake'. It looks much better and rides much nicer.

I installed a voltmeter and also got the oil pressure gauge hooked up. The car originally only had 'idiot' lights for both so at least now I can see what is really going on.

I also developed a slight leak in the passenger side rear axle. So I found a new seal on ebay and bought it. Should have it this week so will tackle that problem next.

I still have a slight vibration at around 2000 rpm. It appeared the tail shaft on the trans could have been hitting the cross member so I put a couple spacers under the mount to raise the trans. It helped but I'm still feeling the vibration. Will have to try to figure that problem out.

Saturday, April 13, 2013

I've accomplished a few things over the last few days.

I got the grill and bumper re-installed after replacing the harmonic balancer and electric fan. New fan works great runs at about 1/4 of the temp gauge all the time now. No overflow or leaks from the radiator.






I also got the roof painted so now the car is all one color!



I re-installed the chrome bed trim around the rear window so all of my trim is now in place





Once the paint is fully dry (normally takes 24 hours) I will wash the whole car and start work on the bed. I did get the first aluminum cross support installed the other day (the rear most one). Now I need to pop rivet it in place. Also got to try out the rust eliminator paint. It appears to have worked but will know more when I prime the spots I tried it on.

Friday, April 5, 2013

Well UPS dropped off the new (rebuilt) harmonic balancer this afternoon. It looks great! I thought about putting off installing it till tomorrow but decided to take the few minutes to do it today. Everything went easy so I pulled the car around front (long story but the neighbor smokes and loves to sit and watch EVERYTHING I do.) and installed the new 14 inch electric fan! Again everything went smooth. Took it out for a quick test drive and the balancer seems to have helped with the 2000 to 2500 rpm vibration. Next step is to check motor mounts and make sure exactly what was done when they put the engine in. Tomorrow I will re-install the front rock shield, grill and bumper.


Friday, March 22, 2013

problems

I ran into a 'glitch' with the new harmonic balancer. Before I pulled everything apart I did a quick measurement and discovered the HB on the car is 7" in diameter and the new one is only 6". So I called the Damper Doctor and he said to go ahead and ship both back to him and he will rebuild mine. Since this project was going to be done in the front of the house I had hoped to not have it take more than a few hours. So I pulled the car into the driveway as far back from the street as I could and went to work. About 2 hours later I had the radiator and balancer off the car. I went ahead and cleaned up the radiator for when I re-install it and also cleaned up my old HB. Should only take a few days so with shipping etc I figure by the end of next week I should get it back.

Here's a picture of both the old and the new balancers.






Also here's a close up of the old balancer with the part number visible. Now I see why I couldn't find it when I was looking for it. It's on the inside (towards the engine)!


Thursday, March 21, 2013

New balancer is here!

UPS just dropped off the new (rebuilt) harmonic balancer from Damper Doctor. I'm surprised how good it looks. Appears to be a brand new one rather than rebuilt.

Hopefully tomorrow I can get it installed and see if my vibration problem goes away!